Skip to content

Menu

Residential electrical load calculator

Enter the floor area, fixed appliances and heating or cooling, and Busbar sizes the service by the NEC optional method for a one-family dwelling, line by line with the code section. It follows NEC 2020, 2023 or 2026, including the 2026 change to 2 VA per square foot, an 8 kVA first tier and EV chargers at 100 %. The calculation is free with no sign-up; Pro is US$9 a month for a permit-ready PDF with your company and the job address. It covers single-family homes on a 120/240 V or 208Y/120 V service, not multifamily or commercial buildings.

  • NEC 2020, 2023 and 2026
  • Every step cited
  • No sign-up
Dwelling load calculator
Dwelling
ft²

20 A kitchen circuits, at least 2

Fixed appliances (nameplate VA or W)
VA
VA
VA
VA
VA
VA
VA
VA
VA
VA
Heating and cooling (nameplate)
VA
VA
VA
VA
VA

They never run at the same time, so the compressor is not added (220.82(C)(3)).

Calculated load 101.2 A: a 125 A service or larger

24,280 VA at 240 V by the 220.82 optional method. Size the service conductors for this load per 310.12.

NEC 2023 · 220.82 optional method, one-family dwelling · 120/240 V

General loads

General lighting and receptacles, 2000 ft² × 3 VA
6,000 VA
Small-appliance circuits, 2 × 1,500 VA
3,000 VA
Laundry circuits, 1 × 1,500 VA
1,500 VA
Range, cooktop or wall oven (nameplate)
12,000 VA
Clothes dryer (nameplate)
5,000 VA
Water heater (nameplate)
4,500 VA
Dishwasher (nameplate)
1,200 VA
Total general load
33,200 VA
First 10,000 VA at 100%
10,000 VA
Remainder 23,200 VA at 40%
9,280 VA
General load after demand factors
19,280 VA

Heating and air conditioning (largest of)

Air conditioning and cooling at 100% — largest, used
5,000 VA

Service

Calculated load
24,280 VA
Calculated load ÷ 240 V
101.2 A
Minimum service rating for a one-family dwelling
100 A
  • The optional method applies only to a one-family dwelling served by a single 120/240-V or 208Y/120-V, three-wire set of service or feeder conductors with an ampacity of 100 A or more (220.82(A)).
  • Electric vehicle supply equipment is included in the general load at its nameplate rating.

Permit-ready PDF report

The same calculation with every NEC reference, your company and the job address, on US Letter. Saved in this browser only.

Pro, US$9/month

How it works

  1. 01

    Enter the house

    Floor area by outside dimensions, small-appliance and laundry circuits, and the nameplate of each fixed appliance, EV charger included.

  2. 02

    Add heating and cooling

    Air conditioning, heat pump and supplemental heat, or electric space heating. Busbar takes the largest of the 220.82(C) choices.

  3. 03

    Read the service size

    The calculated load in VA and amps and the next standard service size, with each line and its section ready to copy or download.

Questions

Standard or optional method: which one is this?

The optional method of 220.82 (120.82 in NEC 2026). It is allowed for a one-family dwelling served by a single 120/240 V or 208Y/120 V service of 100 A or more, and usually gives a smaller service than the standard method.

How are heat pumps counted?

The compressor at 100 % plus supplemental heat at 65 %. If the two are interlocked so they never run together, only the supplemental heat at 65 % is counted. Busbar compares that with the air conditioning and any other heating and uses the largest.

Which NEC edition does Busbar use?

You choose NEC 2020, 2023 or 2026. The 2026 edition moved load calculations from Article 220 to Article 120; Busbar cites the section numbers of the edition you pick. Local amendments are not included, so check what your jurisdiction has adopted.

Can I hand the result to an inspector?

The page shows every step with its NEC section, so you can copy it into your permit packet for free. Pro (US$9 a month) downloads the same calculation as a PDF with your company, license number, customer and job address.

Do I need to sign up?

No. Every calculator works without an account. You only need one, with a verified email address, to subscribe to Pro.

Hand the inspector a clean calculation

Every calculator is free, with the full step-by-step result and NEC references on the page. Pro is US$9 a month for PDF reports with your company and the job address.